Yes we can make bespoke kitchen furniture, but “how bespoke” we hear you ask. “Can I have a void under? Can I add a drawer? Can I have a door and additional shelves?”
The answer to all of the above is YES! You can have all that and more.
Dislcaimer: “We are aware that our photos aren’t all great, afterall we focus on making the furniture, not on becoming photographers! Also we don’t have a huge variety of examples sitting in the warehouse waiting for a photo shoot; we have taken many of the following photos in situ. So we apologise in advance for the poor quality of some of them, but we hope they’re enough to give you an idea of what is possible.”
Here below is a comprehensive list of what you can change on your ‘bespoke’ units:
- You can ask for any length (left-to-right),
- any depth (front-to-back)
- any height
——————————————————————————
You can have an upstand either to rear, to one side, to both sides:
——————————————————————————
You can also have just a partial upstand where the wall ends short of the front:
——————————————————————————
You can increase the height of the upstand, up to 150mm high (no picture)
——————————————————————————
You can have a rear cut out:
——————————————————————————
You an have a corner cut out:
——————————————————————————
You can insert a hand wash basin pretty much anywhere in the top:
——————————————————————————
You can simply insert a bowl:
——————————————————————————
Or you can insert a bowl with anti-drip moulding around it:
——————————————————————————
You can ask for a cut out for any drop-in unit e.g. an ice well:
——————————————————————————
You can have the top profiled for dishwasher baskets:
——————————————————————————
You can add a scrapping ring or a rubbish shute:
——————————————————————————
You can add a chamfer to the front, or to the side:
——————————————————————————
You can have a step in the top to accommodate cooking equipment:
——————————————————————————
You can have an MDF underside- not only does this help it to maintain its structure, it also deadens noise (no picture)
——————————————————————————
We normally make the tops with a 50mm turndown but you can change this, to a minimum of 35mm (no picture)
——————————————————————————
You can change the inset of the legs both to sides and to rear by anything to a minimum of 25mm (no picture)
——————————————————————————
You can have a full void under with just tie bars to the sides and rear:
——————————————————————————
You can have a partial void with shelf to one side:
——————————————————————————
You can have a centre void:
——————————————————————————
You can add as many undershelves as you like (bearing in mind that the more shelves the thinner the useable space inbetween):
——————————————————————————
You can have runners for GN trays or dishwasher baskets:
——————————————————————————
You can add upstands to the rear of the shelves (no picture)
——————————————————————————
You can have one door to front (hinged):
——————————————————————————
You can have multiple doors to front (hinged or sliding):
——————————————————————————
You can have a panel to one side, or two sides, or both sides and rear to enclose the unit (no picture)
——————————————————————————
You can have a valance/part panel to the front or to the sides:
——————————————————————————
You can have one drawer to any side or to the centre:
——————————————————————————
You can have two or more drawers side by side or even back to back if the table is deep enough (no picture)
——————————————————————————
You can have up to 4 drawers stacked:
——————————————————————————
We normally put adjustable height feet:
But you may prefer castors, of which two are braked:
If you have any other ideas in mind let us know! Send us a photo, a picture or a rough sketch of what you need if it’s hard to explain. Ask us any question, ask us also to help you to decide what you would like, we will do our best to help you out!
